• Low 250 g/l VOC
• Covers 250-300 sq. ft. / gallon
• Oil-based formula
• Enhances hardwood stability
• Seals and waterproofs
• Trans oxides add UV protection
• Prevents cupping & warping

• Use on most exotic hardwoods
• Apply to thermally modified wood
• Perfect for new or refurbished wood
• 1 coat application dries in 24 hrs
• Inhibits mold, mildew, rot & decay
• Non-film forming formula
• Semi-transparent tinted stain

Air-Dried Lumber and Composites Gap Spacing 3/32" (2,4 mm)

Air-Dried, Kiln-Dried Lumber and Composites Gap Spacing 5/32" (4mm)

Kiln Dried Lumber, and Composites Gap Spacing 1/4"(6,4mm)

Ipe Oil^® Hardwood Deck Finish is an oil-based natural hardwood finish. It is specifically formulated to protect and preserve the natural beauty of exterior hardwood decking and siding. Ipe Oil^® Hardwood Deck Finish provides excellent penetration of even the densest hardwoods with minimal raising of the grain.

WiseCoat^® Premium Hardwood Deck, Siding & Fence Sealer is a low 53 g/l VOC, non-toxic waterproofing sealant designed for use on hardwood decking, siding and fencing surfaces. WiseCoat^® finish is water-based and guaranteed to prevent excessive water accumulation below the wood surface for up to six (6) years on horizontal surfaces and up to ten (10) years on vertical surfaces when used according to the product instructions.

Use the WiseCable^® Legacy WC-LS Series for any 4x4 hardwood post as an inside to inside fitting on a straight run. The tensioning device is an adjustable body with hanger bolt which is a factory swaged, tensioning, face-of-the-post-mounted fitting. A push lock attaches the same way to the other 4x4 end. 5' up to 50' lengths.

Use the WiseCable^® Legacy WC-LSS Series for any 4x4 hardwood post as an inside to inside fitting on a pitch or stair application. The tensioning device is an adjustable body with threaded eye, which attaches via a mounting screw to the lag eye, threaded tab. A push lock with threaded eye attaches the same way to the other 4x4 end. 5' up to 20' lengths.

Use the WiseCable^® Estate WC-ES Series for any 4x4 wood post as an outside to outside fitting on a straight level run, or on a pitch, or stairs. The tensioning device is a 3½” long invisible receiver, which installs through the wood post on one end. The invisible receiver with invisible stud combination is a concealed, swaged, tensioning, through-the-post-mounted fitting. A pull lock fitting is installed through the other 4x4 end. 5' up to 50' lengths.

The WiseCable^® Heritage WC-HS Series is a budget-friendly cable railing kit for any 4x4 wood post as an outside to outside fitting on a straight level run, or on a pitch, or stairs. The tensioning device is a 2-7/8” long threaded stud which installs on the back side of one end post. This through-the-post configuration is the only scenario in which the threaded stud may be used. A pull lock fitting is installed through the other 4x4 end. 5' up to 50' lengths.

There’s no pre-drilling required with our new DeckWise^® 8-18 Heat-Treated Deck Screws. The four-sided tips can penetrate the most dense exotic hardwoods, and the serrated thread design helps prevent your deck boards from splitting or splintering, even when screwing near the edge.

Choose #8x1-3/4" and #8x2" lengths.

The DeckWise^® brand of stainless decking screws are a great way to ensure hardwood and composite deck boards stick tight to the joist. DeckWise^® Colormatch decking screws are made from high-quality 305 & 316 grade stainless steel for optimum performance. Choose from 6 painted head colors.

Choose #8x1", #8x1-1/2", #8x2", #8x2-1/2" or #8x3-1/8" lengths.

Our 305 Grade stainless steel Composite and PVC deck building screws come in 5 different painted head colors to match your material. Specially designed to reduce unsightly mushrooming which could arise when using composite stock. Screw flutes also grab tight pulling the board snug to the framework underneath.

Available in #10x2-1/2" length.

These Xylan coated screws are tough enough to drill through metal joists and the load-bearing shaft area remains forgiving and resistant to stress cracking. They a high performance 410 Grade stainless steel screw which allows Pro builders and DIY installers a uniform and long-lasting solution for metal joist decks.

Choose #7x1-5/8" or #7x2-1/4" lengths.

Crafted from solid stainless steel, DeckWise^® Hidden Siding Fasteners create a sleek and upscale look. The entire system is designed to significantly reduce cupping, twisting, and mold growth due to water penetration. Perfect for both residential and commercial applications, the DeckWise^® Hidden Siding Fastener system works with most rainscreen siding profiles.

When this barrier tape is applied to the top of deck joists, over ledger boards, and around support posts, it creates a waterproof seal that helps stop decay and wood rot. Rot is caused by moisture that stays in contact between the decking and the framing as well as through screw holes. This tape also self-seals around penetrating fasteners.

DeckWise^® spacers are a great addition to your deck building toolbox. The versatile design allows you to use these board spacers in any position between boards. And, with the bright color-coded design, finding the right spacer is now much easier than other generic, disposable brands on the market.

DeckWise^® Hardwood Deck Tile System and Connectors give Contractors, Architects, DIY Homeowners, and even Renters a quick and easy way to construct semi-permanent decking or to renovate living spaces. The DeckWise^® Hardwood Deck Tile System can be tailored to any specific need or application.

NEW! Choose 12"x12", 20"x20" or 24"x24" tiles in solid Ipe, Cumaru, Tigerwood or Massaranduba.

DeckWise^® Router Bits have been specifically designed to create a perfectly symmetrical groove to accept Ipe Clip^® Hidden Deck Fasteners. The 4-wing design provides a smooth cut for creating slots and grooves in decking material. Bit arbor sizes availble in 1/4" and 1/2" diameters to fit most router devices.

The DeckWise^® Hardwood Plug Cutter Bits are convenient for on the job use and allow contractors and builders to cut custom plugs whenever needed. Fresh cut plugs on the job will guarantee a perfect match of color and grain characteristics. Plug sizes availble are 3/8" and 1/2" to match most hardwood decking and siding applications.

Ipe Seal^® is a wax emulsion end grain sealant proven to increase the structural integrity of hardwoods. Once applied to freshly cut, exposed end grain, Ipe Seal^® creates a bond that extends the life of each board while also preventing end-checking (splitting) and unsightly cracks.

The NEW DeckWise^® Hardwood Deck Maintenance Kit is a specially assembled kit which includes everything Homeowners and Contractors need to maintain the natural wood color of hardwood decking. Our new kit is perfect for Ipe deck maintenance, as well as maintaining other hardwood decks using hidden fasteners.